User manuals A-z

IMPORTANT NOTES:

Stalon Accessory mounts are pefect for attaching cameras, search lights, anher cessories. It is however important that the setup with weapon and silencer is tested for accuracy and point of impact.

INSTRUCTION:

Make sure that the Stalon accessory mount fits the model of silencer it is intended for. Install the accessory mount on the back-end of the silencer and attach the silencer with accessory mount mounted to the weapon it is intended for. Align the accessory mount to the correct position and secure it by clamping the weaver style base with a ring mount or similar. Test shoot the setup for accuracy and point of impact.

IMPORTANT NOTES:

Stalon barrel support is made of extremely heat-resistant composite. If the material deforms or melts, you have exceeded the silencer's maximum temperature limit. A melted barrel support can be replaced, and in some cases, the thread needs to be cleaned. Note that the barrel's temperature will be higher and affect the temperature the barrel support is exposed to. The Stalon barrel support should be adjusted to the diameter of the weapon's barrel, 0.5-0.7mm larger than the barrel's diameter. Accuracy will be negatively affected if the barrel bushing is in contact with the barrel.

INSTRUCTION:

Make sure that the Stalon barrel support fits the model of silencer and the diameter of the weapon barrel. Make sure to adjust the barrel support by milling or drilling the hole to the correct diameter (0,5-0,7mm larger than the barrel). This should be done by a professional person. Attach the barrel support by screwing it on to the back-end of the silencer. Check the barrel support to make sure it is not touching the barrel of the weapon.

IMPORTANT NOTES:
‍
Stalon barrel support is made of extremely heat-resistant composite. If the material deforms or melts, you have exceeded the silencer's maximum temperature limit. A melted barrel support can be replaced, and in some cases, the thread needs to be cleaned. Note that the barrel's temperature will be higher and affect the temperature the barrel support is exposed to. The Stalon barrel support should be adjusted to the diameter of the weapon's barrel, 0.5-0.7mm larger than the barrel's diameter. Accuracy will be negatively affected if the barrel bushing is in contact with the barrel.

INSTRUCTION:

Make sure that the Stalon Barrel support fits the model of silencer and the diameter of the weapon barrel. Make sure to adjust the barrel support by milling or drilling the hole to the correct diameter (0,5-0,7mm larger than the barrel). This should be done by a professional person. Attach the barrel support by screwing it on to the back-end of the silencer. Check the barrel support to make sure it is not touching the barrel of the weapon.

IMPORTANT NOTES:
‍
None.

INSTRUCTION:
‍
Make sure that the Stalon front-end fits the silencer it is intended for. Attach the Stalon front-end to the silencer by first removing the "original" front-end on the silencer. Test shoot the setup for accuracy and point of impact.

IMPORTANT NOTES:
‍
Installation of a reator should only be carried out by an experienced- or professional person or gunsmith.

INSTRUCTION:

Installation of a gas regulator should only be carried out by an experienced- or professional person or gunsmith.

IMPORTANT NOTES:

Installation of a as regulator should only be carried out by an experienced- or professional person or gunsmith.

INSTRUCTION:

Installation of a gas regulator should only be carried out by an experienced- or professional person or gunsmith.

IMPORTANT NOTES:
‍
None.

INSTRUCTION:

Make sure that the Stalon MIMIC muzzle brake fits the weapon it is intended for .Attach the muzzle brake to the weapon firmly. Test shoot the setup for accuracy and point of impact.

IMPORTANT NOTES:

None.

INSTRUCTION:
‍
Make sure that the Stalon muzzle brake fits the weapon it is intended for. Attach the muzzle brake to the weapon firmly and, if necessary or wanted, screw in included adjustment screws for perfect recoil taking. Test shoot the setup for accuracy and point of impact.

IMPORTANT NOTES:

Never use the Stalon neoprene cover over the recommended temperatur limit (250°C), Neoprene loses its elasticity at high temperatures.

INSTRUCTION:
‍
Make sure that the Stalon neoprene cover fits the model of silencer it is intended for. Put the neoprene cover over the silencer and make sure it is covering the whole silencer. If the neoprene cover has a cordura reinforcement, make sure it is aligned on the top of the silencer when attached to a weapon.

IMPORTANT NOTES:

Stalon pen sights fit most weapon/silencer combinations, it is however important that the combination is tested for accuracy and point of impact. The open sight stays perfectly aligned if attached correctly, even if the silencer is removed from the weapon and attached again.

INSTRUCTION:

Open sights X-series
‍
Make sure that the Stalon open sight for X-series fits the model of silencer it is intended for. Install the open sight on the front-end of the silencer and attach the silencer with open sight mounted to the weapon it is intended for. Align the open sight with the sights on the weapon, secure the positioning of the open sight by screwing the locking bolt on the top of the open sight. Test shoot the setup and adjust sideways if needed.

INSTRUCTION:

Open sights VICTOR-series

Make sure that the Stalon open sight for VICTOR-series fits the model of silencer you have. Put the open sight on the back-end of the silencer and attach the silencer with open sight mounted to the weapon it is intended for. Align the open sight with the sights on the weapon, secure the positioning of the open sight by screwing the locking bolt on the underside of the open sight. Test shoot the setup and adjust sideways if needed.

IMPORTANT NOTES:

For lubricating thread on the weapon and split section of some silencer.

INSTRUCTION:

Lubricate the thread on the weapon by applying Stalon silencer grease on the weapon thread. Lubricate the thread in the split section of some silencers by applying Stalon silencer grease on the thread.

IMPORTANT NOTES:

Stalon thread adaptors should always be attached firmly to the weapon, not to the silencer.

INSTRUCTION:

Make sure that the Stalon thread adaptor fits the model of silencer and the thread on the weapon. Clean the thread on the weapon and apply Loctite, attach the thread adaptor firmly on the weapon and wait for the Loctite to harden. Attach the silencer to the thread adaptor and test shoot the setup to make sure the accuracy is perfect.

IMPORTANT NOTES:

None.

INSTRUCTION:
‍
Make sure that the Stalon thread cover fits the thread on the weapon it is intended for.